Windows 95/98 DUN and RAS Error Codes

DUN & RAS ERROR CODES

Windows 95 & Windows 98 

Error Code

  Message / Explanation

600   An operation is pending
601   The port handle is invalid
602   The port is already open
603   CallerÂ’s buffer is too small
604   Wrong information specified
605   Cannot set port information
606   The port is not connected
607   The event is invalid
608   The device does not exist
609   The device type does not exist
610   The buffer is invalid
611   The route is not available
612   The route is not allocated
613   Invalid compression specified
614   Out of buffers
615   The port was not found
616   An asynchronous request is pending
617   The port or device is already disconnecting
618   The port is not open
619   The port is disconnected
620   There are no endpoints
621   Cannot open the phonebook file
622   Cannot load the phonebook file
623   Cannot find the phonebook entry
624   Cannot write the phonebook file
625   Invalid information found in the phonebook
626   Cannot load a string
627   Cannot find a key
628   The port was disconnected
629   The port was disconnected by the remote machine
630   The port was disconnected due to hardware failure
631   The port was disconnected by the user
632   The structure size is incorrect
633   The port is already in use or is not configured for DUN/RAS dial-out
634   Cannot register your computer on the remote network
635   Unknown error
636   The wrong device is attached to the port
637   The string could not be converted
638   The request has timed out
639   No asynchronous net available
640   A NetBIOS error has occurred
641   The server cannot allocate NetBIOS resources
642

  One of your NetBIOS names is already is already registered on the

  remote network

643   A network adapter at the server failed
644   You will not receive network access pop-ups
645   Internal authentication error
646   The account is not permitted to log on at this time of day
647   The account is disabled
648   The password has expired
649   The account dies not have Remote Access permission
650   The Remote Access server is not responding
651   Your modem (or other connecting device) has reported an error
652   Unrecognized response from the device
653

  A macro required by the device was not found in the device INF file

  section

654

  A command or response in the device INF file section refers to an

  undefined macro

655   The macro was not found in the device INF file section
656   The macro in the device INF file contains an undefined macro
657   The device INF file could not be opened
658   The device name in the device INF or media INI file is too long
659   The media INI file refers to an unknown device name
660   The device INF file contains no response for the command
661   The device INF file is missing a command
662   Attempted to set a macro not listed in the device INF file
663   The media INI file refers to an unknown device type
664   Cannot allocate memory
665   The port is not configured for Dial-Up Networking/Remote Access
666   Your modem (or other connecting device) is not functioning
667   Cannot read the media INI file
668   The connection dropped
669   The usage parameter in the media INI file is invalid
670   Cannot read the section name from the media INI file
671   Cannot read the device type from the media INI file
672   Cannot read the device name from the media INI file
673   Cannot read the usage from the media INI file
674   Cannot read maximum connection BPS rate from the media INI file
675   Cannot read the maximum carrier BPS rate from the media INI file
676   The line is busy
677   A person answered instead of a modem
678   There is no answer
679   Cannot detect a carrier
680   The is no dial-tone
681   General error reported by device
682   ERROR WRITING SECTIONNAME
683   ERROR WRITING DEVICETYPE
684   ERROR WRITING DEVICENAME
685   ERROR WRITING MAXCONNECTBPS
686   ERROR WRITING MAXCARRIERBPS
687   ERROR WRITING USAGE
688   ERROR WRITING DEFAULTOFF
689   ERROR READING DEFAULTOFF
690   ERROR EMPTY INI FILE
691   Access denied because username and/or password is invalid on
the domain. (check your password)
692   Hardware failure in port or attached device
693   ERROR NOT BINARY MACRO
694   ERROR DCB NOT FOUND
695   ERROR STATE MACHINES NOT STARTED
696   ERROR STATE MACHINES ALREADY STARTED
697   ERROR PARTIAL RESPONSE LOOPING
698   A response keyname in the device .INF file is not in the expected
format
699   The device response caused buffer overflow
700   The expanded command in the device .INF file is too long
701 The device moved to a BPS rate not supported by the COM driver
702   Device response received when none expected
703   ERROR INTERACTIVE MODE
704   ERROR BAD CALLBACK NUMBER
705   ERROR INVALID AUTH STATE
706   ERROR WRITING INITBPS
707   X.25 diagnostic indication
708   The account has expired
709   Error changing password on domain
710   Serial overrun errors were detected while communicating with your
modem. (Com Over run)
711   RasMan initialization failure. Check the event log
712   Biplex port is initializing. Wait a few seconds and redial
713   No active ISDN lines are available
714   Not enough ISDN channels are available to make the call
715   Too many errors occurred because of poor phone line quality
716   The Remote Access IP configuration is unusable
717   No IP addresses are available in the static pool of Remote Access
Access IP addresses
718   PPP timeout
719   PPP terminated by remote machine
720   No PPP control protocols configured
721   Remote PPP peer is not responding
722   The PPP packet is invalid
723   The phone number, including prefix and suffix, is too long
724   The IPX protocol cannot dial-out on the port because the computer is
an IPX router
725   The IPX protocol cannot dial-in on the port because the IPX router is
not installed
726   The IPX protocol cannot be used for dial-out on more than one port at
a time
727   Cannot access TCPCFG.DLL
728   Cannot find an IP adapter bound to Remote Access
729   SLIP cannot be used unless the IP protocol is installed
730   Computer registration is not complete
731   The protocol is not configured
732   The PPP negotiation is not converging
733   The PPP control protocol for this network protocol is not available on
available on the server
734   The PPP link control protocol terminated
735   The requested address was rejected by the server
736   The remote computer terminated the control protocol
737   Loopback detected
738   The server did not assign an address
739   The remote server cannot use the Windows NT encrypted password
740   The TAPI devices configured for Remote Access failed to initialize or
were not installed correctly
741   The local computer does not support encryption
742   The remote server does not support encryption
743   The remote server requites encryption
744   Cannot use the IPX net number assigned by the remote server.
Check the event log
752   A syntax error was encountered while processing a script


Would you rather go back to the beginning?   Then click..


 

About Dewwa Socc

Sahifa Theme License is not validated, Go to the theme options page to validate the license, You need a single license for each domain name.